Genotropin Pen. Replaced with popeyepen same thing more iu

Before You Begin

To help prevent infection, always wash your hands with soap and water before preparing or using the GENOTROPIN PEN 12.

• Remove the front cap from the GENOTROPIN PEN 12.
• Unscrew the metal front part and detach it from the plastic body of the pen.
• Remove the paper covering from the back of a new needle.
• Screw the needle onto the metal front part by gently turning it clockwise (to the right).

• Use only the 12mg cartridge.
• Wipe the metal/rubber tip of the cartridge with an alcohol swab.
• Insert the cartridge into the metal front part of the pen, with the metal/rubber tip towards the needle end. Push the cartridge firmly into place.

• Press the red release button to release the black/white injection knob.
• Turn the black/white injection knob counterclockwise (to the left) as far as it will go.
• Check that the plunger rod is not visible through the window at the top of the plastic body of the pen. Do NOT proceed if the plunger rod is visible, as the medication will not be properly mixed. Instead, press the red release button again to draw back the plunger rod. After the rod is no longer visible through the window, proceed to the next step.

• Hold the metal front part upright.
• While holding upright, gently screw the metal front part and the plastic body back together. This mixes the diluent in the rear chamber of the cartridge with the growth hormone powder in the front chamber.
• Gently tip the assembled GENOTROPIN PEN 12 from side to side to help dissolve the powder completely. DO NOT SHAKE as that might inactivate the growth hormone.

• Look through the cartridge windows in the metal front part of the pen and make sure the drug solution is clear. If you see particles or if the solution is discolored, DO NOT INJECT IT. Instead, call the toll-free number listed at the end of these instructions.
• Remove the outer needle cap and save it for later.
• Remove and discard the inner needle cap. Be careful not to touch the exposed needle.
• Remove any trapped air from the solution as follows:

Turn the black/white injection knob

clockwise (to the right) one click. This will line up the white mark on the injection knob and the black mark on the body of the pen.

Hold the GENOTROPIN PEN 12 upright and gently tap the metal front part with your finger to move any air bubbles to the top.

Push the black/white injection knob all the way in. You will see a drop of liquid appear at the needle point. Any trapped air has now been released.

• • If desired, attach the reusable needle guard over the needle—push until it snaps in place. Again, be careful not to touch the exposed needle. To avoid an accidental needle stick, grip the sides of the needle guard; never push on the end.

• Press the red release button to reset the device.
• The black/white injection knob will pop out and the dose display window will read 0.0.
• With the dose display activated, turn the black/white injection knob clockwise (to the right) until your prescribed dose is displayed.
• If you go too far, just turn the knob back the other way until the correct dose is displayed. NOTE: If you turn the black/white injection knob backwards beyond zero after a cartridge has been inserted, the pen display will show (-

-). Just turn the injection knob forward (clockwise) until numbers reappear on the dose display.

• • • The GENOTROPIN PEN 12 contains a battery for the dose display. To save the battery’s energy, the dose display is activated for two minutes and then automatically disappears. Although the display is no longer visible, the dose remains available for delivery. NOTE: Each click of the black/white injection knob equals a two-tenth-of-a milligram dose (or 0.2 mg). One click—or 0.2 mg—is the minimum possible dose per injection; 20 clicks—or 4.0 mg—is the maximum possible dose per injection. If you accidentally dial more than the maximum 4.0 mg dose, some liquid may emerge from the tip. This is normal and will not affect your injection—simply dial back to the correct

dose.

• Select and prepare an appropriate injection site, as directed by your healthcare provider.
• Pinch a fold of skin at the injection site firmly, and push the GENOTROPIN PEN 12 into the skinfold at a 90° angle. Push the pen down as far as possible.
• Push the black/white injection knob until it clicks. Wait at least 5 seconds and then withdraw the GENOTROPIN PEN 12.

• Remove and store the needle guard, if you used one.
• Carefully replace the outer protective cap on the needle, as instructed by your healthcare provider.
• Unscrew the needle and discard it in a proper disposal container. NEVER REUSE A NEEDLE.
• Replace the front cap, then put the GENOTROPIN PEN 12 back in its protective case. Store it in the refrigerator at 2° to 8°C (36° to 46°F) until your next injection.

Your Next Injection

If you already have a drug cartridge in your GENOTROPIN PEN 12, prepare the pen and administer your dose as follows:

• Remove the front cap of the GENOTROPIN PEN 12.
• Remove the paper covering from the back of a new needle.
• Screw the needle onto the metal front part of the pen by turning it clockwise (to the right).
• Remove the outer and inner needle caps.
• Follow the instructions above, starting with step 6.

To Replace the Cartridge

• Press the red release button to reset the GENOTROPIN PEN 12.
• Turn the black/white injection knob counterclockwise (to the left) as far as it will go.
• Unscrew the metal front part and remove the empty cartridge.
• Discard the empty cartridge as instructed by your healthcare provider.
• To insert a new cartridge and prepare the GENOTROPIN PEN 12 for use, follow the instructions above.

Storage

Between uses, store your GENOTROPIN PEN 12 in the refrigerator at 2° to 8°C (36° to 46°F) in its protective case. Always remove the needle before storing. Do not freeze. Protect from light. Discard the cartridge in your GENOTROPIN PEN 12 within 28 days after reconstitution (mixing of the growth hormone powder with the diluent) even if the cartridge is not empty.